Product Description

Screen filter for PSP. Protects PSP screen from getting dirt and scratches. Re-usable

Product Details

• Amazon Sales Rank: #4499 in Video Games
• Brand: Hori
• Model: UHPP-01
• Released on: 2008-05-06
• Platform: Sony PSP
• Dimensions: .50" h x 3.50" w x 5.50" l, 1.00 pounds

Features

• Screen filter for PSP
• Protects PSP screen from getting dirt and scratches
• Re-usable filter

Customer Reviews

Well Worth Having
A PSP screen is clear and large - and is almost a magnet for fingerprints, dust and scratches. This filter helps to protect it from damage.

In essence it's a clear plastic layer that you place down with a sticky substance on your PSP screen. You need to clean your screen VERY well to start with. We have eyeglass cleaner in the house and it worked perfectly - not a speck of dust or lint was left when we began.

Then we carefully followed their instructions to lay down the screen. It went down without any problem at all, and was crystal clear once it was down. Playing through it did not present any issue, and it really does a good job of keeping oils and dust away from the actual screen surface.

Highly recommended!

The secret of applying this filter
Many people have problem applying the filter. If you just peel off and apply the sticker directly, you will face the following 3 major problem:

1. Dust particles
2. air bubbles (or known as air pockets, caused by air or dust)
3. Sticker orientation accuracy

To solve the above problems, here is the secret and the correct steps, not limited to this PSP filter, in fact, this secret applied to all stickers application.

Do the following steps, and you will be amazed with the result.
Ingredients:
a. The screen protector filter
b. Bowl
c. hand soap, body shampoo (lotion, etc.. anything alcaline based will do)
d. water
e. plastic paper credit card sized or smaller which act as your lifter. Optional, use the front/back plastic cover for the sticker will do as well.
f. tissue paper

Step

1. Wipe the PSP screen clean
2. Fill the bowl with one or two teaspoon amount of hand soap and dilute it with half bowl of water.
3. scoop out the bubbles in the bowl as many as possible.
4. Remove both front and back side of the filter. (remember the up-side)
5. Soak the filter into the bowl and take it out with your plastic paper. (try not to use finger)
6. Apply the filter gently (while it is still little wet)

7. Adjust the filter to the correct position desired.
8. Push the liquid out with a credit card from middle to outside.
9. Wipe any water that squeezed out from the corner of the sticker as soon as soon you see it.
10. If you see dust particle (a small air pocket with a little dust dot in the middle) inside the sticker, lift it up with a plaster paper, remove the dust, and close it back.

11. repeat step 7 to 10 until it is completely dry and up to your desire.

If application is not as your desired, remove the sticker, soak it back to the same bowl, clean the sticker to make sure no dust particles with the same way you lean your contact lens, and reapply. (No, you don't have to throw your filter!)

Finally you got yourself a perfect application of filter and air bubble-less.

This is the same technique as applying tinted film/stickers on glass windows, car windows and wind screen by the car assessories professionals. The only difference is they spray soap water on the filter instead of using a bowl (coz PSP filter is so small compared with filter for tinted glass application)

Try it, you will be amazed by the result instead of apply directly without soap water.

Excellent Product for an Excellent Price - Make sure to follow the directions
This is an excellent screen filter/protector for the Sony PSP. It reduces the glare on the screen, it's scratch resistant and doesn't show finger prints as easily as the PSP screen. The instructions aren't 100% clear and I can see how this product has gotten some negative reviews on other sites. However, the key is to understand that filter/protector is in between the sheet with the red tab and the sheet with the clear tab. For those that say they have bubbles or the filter is too thin, they probably applied the sheet with the red tab (which is what I did initially). After noticing the filter was stuck to the sheet with the clear tab, I removed it and applied it to the PSP. No bubbles or anything. Also the filter comes with with a cloth to clean both the screen and the filter.

My one complaint would be that Hori should have made the two sheets with a color (not clear like the filter) so you could tell the different between the sheets and the actual filter. Other than that, top notch product for an extremely good price.