Product Description

The new Actiontec USB/Ethernet DSL Modem with Routing Capabilities is really two devices rolled into one. It's a full rate ADSL modem that's upgradeable to the new, faster ADSL 2/2+protocol. And it's a router, capable of networking up to two computers, via wired ports, with a minimum amount of hassle. So, get rid of the clutter of components on your desk and replace them all with the Actiontec USB/Ethernet DSL Modem with Routing Capabilities.

Product Details

• Brand: Actiontec
• Model: GEU003AD3A-01
• Platform: Windows
• Format: CD
• Dimensions: 4.00" h x 9.50" w x 12.00" l, 2.80 pounds

Features

• Supports UPnP Plug-and-Play installation for systems with Windows Operating Systems (98, 98SE, Me, 2000 and XP)
• Support One ADSL WAN port (RJ11)
• Compliant with full-rate ANSI T1.413 Issue 2, ITU G.992.1 (G.dmt) and G.992.2(G.lite) standard
• Auto-handshake for different ADSL flavors
• Compliant with USB 1.1 device specification

Customer Reviews

Not For The Faint of Heart
Replaced my 9-year-old Alcatel 1000 modem sitting in front of a Linksys Wireless router. Works fine now, but here was my experience for the rest of you trying to avoid paying your service provider for the installation and an overpriced modem...

1. The Alcatel was so old that the physical wires in the RJ45 jack were different than was expected w/the new Actiontec (and apparently any modem more modern than the Alcatel). Thank goodness, an AT&T phone tech pulled that one out of some obscure corner of his head based purely on the flashing DSL light on the Actiontec, a modem he had never heard of. Took some wiggling around, but I managed to switch the wiring from the two outer contacts to the two inner, and got the DSL to sync.

2. The virtual circuit and virtual path settings were 0 and 35 by default on the Actiontec (not that I knew what that was before this exercise). The Alcatel wanted 8 and 35. Unfortunately, this is something set at the central office at AT&T, in my case specifically for the Alcatel. But it turns out you can change the setting on the Actiontec itself using their web interface, which I did. Reset it, and like magic, all four little lights glowed bright green, including the one saying I was connected to the Internet.

3. Sadly, the story was not over at that point. I could not figure out any way to get to the Internet. No gateway ping, no nothing. I finally figured maybe something was screwed up on the AT&T side. Sure enough, the next AT&T tech I talked to found that someone there had reset my account from a static IP address (something they used to hand out years ago) to PPPoE. They reset that back, and I could connect.

4. Next adventure: getting it to work in front of my Linksys router. Long story short, although this device is also a router, the only way I could get it to work was to use the Actiontec as a dumb modem. In the end that's fine. Took a bit of Googling to sort it out, though, which might be tough if you don't have an Internet connection. The Actiontec docs and web site are non-existent on the topic.

In hindsight, I could have saved some hassle by asking AT&T what modems they supported, because this wasn't one of them. Consult your ISP! Still, AT&T technical people were -- to my surprise -- fantastic and worked with me to sort out the issues regardless. A brief interlude with Actiontec support was the usual useless rote recommendations and "try this" scripted stuff without any noticeable knowledge before I gave up there. Maybe the out-of-box install and configuration will work for you, but it was obviously a lot more complicated than that for me, and I entered into it expecting no problems. To be fair, though, the problems were not Actiontec's, which is why I'm rating it three stars. Good luck!

Worked much better than the vendor provided modem
When I signed up for DSL, my vendor (AT&T) shipped me a free DSL modem. While the provided modem worked most of the time with a computer, it did not reliably run with a router attached. I reconfigured it for a bridged mode and that seemed to improve. However it was still slow, slow to connect as it did not seem to keep connected. The documentation was very dated, with nothing updated on the Internet. The support for that modem really didn't exist from the vendor either. However when I purchased the Actiontec modem after reading the reviews, I was hopeful that it would solve my DSL reliability concerns. When it arrived, I simply followed the instructions which really consisted of plugging it up and turning it on. It self sensed my AT&T vendor by configuring the DSL network settings and began to work. I did nothing. It just worked and is still working. Much faster than the old modem too. I have to say that this new modem looks a bit cheap and flimsy, but it is not and it works beautifully.

Great product
I use this modem with bellsouth internet service and it has been working great. If you are looking for a reliable, easy to configure and use, top quality DSL modem at an affordable price this is the one.